One size - only one single diaper
You only need this diaper from your child is about 6 kg to 18 kg. That is, it is a one size diaper that grows with the baby. It can be set in three sizes with rise snaps at the front of the diaper. That way, you can always get the diaper to fit your child.
Snap-In AIO diaper
AIO (all-in-one) is the term for a cloth diaper, where inserts and diaper has been sewn together.
Elskbar Natural Snap-In is an AIO diaper, but with our clever design, inserts can be unsnapped, which will shorten the drying time significantly. The entire diaper needs to be washed after use, as the diaper shell has a built-in absorbency and gets wet.
We call this type of diaper a Snap-In AIO.
Inserts made of natural materials
The two included inserts are made of the softest and most absorbent natural materials – bamboo and organic cotton. There is a long insert and a smaller booster, both of which are of three layers. With these inserts you are guaranteed plenty of absorbency while the diaper is not going to be too big. Inserts can be snapped into the waterproof diaper shell to prevent them from moving around when your baby is active.
Elskbar is created for the modern and conscious parents who prioritize both the child's health and Mother Earth. The print is made so that the eyes rest and make you think about the nature that we have to take care of.
Absorbency as needed
If your child pees a little, you can choose to only use the small booster and have a nice trim fit.
If your child pees a lot you can use the long insert that folds double.
You can use both inserts if your child pees a lot, for naps or night.
When using both inserts the diaper has 9 super absorbent layers and if you fold the long insert a second time it turns into 12 layers of absorbency. That’s a lot.
This way, you can vary and adapt absorbency to your child’s needs.
The waterproof diaper shell
The waterproof part of the diaper is made of the material TPU. Often, cloth diapers have PUL as the waterproof outer layer, but it is produced by a chemical process that is not that environmentally friendly. TPU, on the other hand, is manufactured during heat treatment and is therefore free of chemical glue. We are proud to offer cloth diapers with TPU.
The inside of the diaper shell has a layer of bamboo terry which gives the diaper an extra layer of absorbency and at the same time it is soft and gentle against your child’s skin.
Freedom to move and a good fit
There is no doubt that Natural Snap-In fits really well on most children. It is narrow between the legs, not too big on the bum, and has a snug fit around the legs without tightening too much. Together, it allows your child to move freely without being inhibited by a big diaper. The good fit will not allow any leaks.
It is important to put the diaper on your child in the correct way. Therefore, we recommend that you look carefully at our fitting guide. When you know how to put on a diaper you have a better chance to succeed with cloth diapers.
Specifications
Diaper shell
- Outer material
- 100% polyester with TPU laminate
- Inner material
- 85% bamboo
- 15% polyester
Insert
- Material
- 70% bamboo
- 30% organic cotton
Washing instructions
Wash
- How to wash a cloth diaper
-
The entire diaper should be washed after use. Just snap off the inserts before washing. The diaper has to be washed at max 60 degrees with a cold prewash. Avoid detergents containing fabric softeners, optical brighteners, or chlorine bleach.
See detailed washing instructions for cloth diapers.
Drying
- How to dry a cloth diaper
-
We recommend hanging the insert to dry, but they can be tumbled on low heat if needed. The waterproof diaper shell, on the other hand, may not dry in the tumble dryer, as the heat can damage the waterproof TPU coating and shorten the life of the rubber bands.
See detailed guide to drying cloth diapers.
